Accueil » Catalogue » RC4/RC6 Accessories » CM42 Mon compte  |  Panier  |  Commander   
English Deutsch Français Svenska
RC6 Lampe de poche
RC4 Lampe de poche
RC4/RC6 Accessories
LED Emergency Light
LED Flash Beacon
News & RoadMap
SecuriLed Introduction
vidéos de test de produit
Stratégie de prix
Résultat du test
Livraison & retour
Sur Nous
conditions de garantie
Mots-clef pour trouver un produit
Recherche avancée
CM42 Module de recharge

Toute information sur cette page n'est actuellement accessible qu'en langue anglaise.

SecuriLed CM42 Charger Module RC4 RC6 Torch

SecuriLed RC4 Accessory: Charger Module CM42

Some Customers have requested a way to recharge the RC4 without removing the battery.
The solution is the Charger Module CM42.

The CM42 is to be permanently placed between the head and the battery tube.

Top: RC4 with CM42 mounted mounted on a RC4  --  Bottom: The CM42 with displayed charger hole

Due to SecuriLed System Logic, this is easily done by simply detach the Torch head from the battery tube, insert the Contact Washer and then screw the CM42 clockwise into the head and attach the battery tube last.

We recommend you to always place the included Contact Washer between Head and CM42 as some early generation RC4's might otherwise have cathode connection problems.

The Torch will be slightly longer after this modification, but it will still fit the original holster as the tail will protrude from the bottom of the holster.

Lift sealing rubber ring to charge the Torch

The CM42 is using a 3,5mm round-pin charger connector, same standard pin as SecuriLed RC4 standard charger.
The Pin hole is protected by a strong silicone sealing ring that will make the charger-hole waterproof but still allow for gas release in case of overpressure inside the Flashlight.

When battery needs to be charged, lift the sealing silicone ring at the Flash-arrow position, plug in the charger-pin. The battery will now be charged.

Note! Driver head module circuit will be disconnected and power circuit will be reversed during charging.
That means the Torch needs to be switched ON for charging. (To allow back-flow circuit)
The charging circuit will otherwise be unclosed and no charging will take place.


RC4 with CM42 in wall-mount RM1

RC4 with CM42 during charging

The benefit of using a CM42 is that the battery never needs to be taken out for charging.

Charger indication will be same as for normal charging. A green LED means no or completed charging (no active current) and a red LED means charging in progress.

Note! Accumulator life is dependant on charging cycles. Better to make complete charging cycles than short burst charging as this will reduce battery life.

Comparison normal RC4 versus RC4 with mounted CM42


If you order a new RC4/RC6 and a CM42 and want them pre-assembled from us, please state so at the text message box during order.

Ce produit a été ajouté à notre catalogue le Wednesday 09 November, 2011.
Les clients qui ont acheté ce produit ont aussi acheté
RC6 Upgrade Head
RC6 Upgrade Head
Double-Set Weapon Mount
Double-Set Weapon Mount
Tactical Wire-Switch
Tactical Wire-Switch
SecuriLed RC6-IV
SecuriLed RC6-IV
Batterie Rechargeable 18650 Li-Ion
Batterie Rechargeable 18650 Li-Ion
Panier plus
... Vide
Nouvelles informations


Our New High performance 560LM RC6 is AVAILABLE NOW!

Need a very small Flashlight?

Try our PiccoloTube for RC4 and RC6!

Interested in a RC6, but already have a RC4?

Try our RC6 Upgrade Head

Do you know that you can order personal engraving Online?

Perfect for a gift or to personalize your RC4/RC6!




Critiques plus
Ecrire une critiqueÉcrire une critique sur ce produit

Copyright © 2018 SecuriLed
Propulsé par osCommerce